Page History
| Table of Contents |
|---|
Full screen mode
Clicking the full screen icon in the header displays all the camera feeds in full screen mode. Clicking the full screen icon in a single camera panel displays the single camera feed in full screen mode.
- The Slider component at the bottom is available in full-screen mode.
The whole camera layout can be set to full-screen mode, not just a single media stream.
| Tip |
|---|
To exit full screen mode
|
Camera panel
Camera settings can be adjusted by clicking on the icons in the right upper corner of the camera panel:
Audio setting: The audio of a particular camera can be turned on or off by clicking the Toggle Audio on/off in the top right corner of the camera panel.
Full screen icon: Clicking the full screen icon in a camera panel displays the camera feed in full screen mode.
| Info |
|---|
| Only one camera of a room can have its audio turned on at a time. |
| Warning |
|---|
The sizing of camera streams might not be optimal (an additional black bar/stripe might be visible at the upper and lower edges of the screen) with a 4:3 video size (aspect ratio). The recommended ratio is 16:9 (e.g. 1280x720), which can be set within the Camera settings window of the Cameras page, in the System Module. |
PTZ functionalities
The following pan-tilt-zoom (PTZ) functionalities are available during recording, to improve camera movements:
On-Screen PTZ: Click in the center of the video
, drag the crosshair and pull the camera into the desired direction. The movement of the camera will stop by releasing the mouse.
Note title IMPORTANT On-Screen PTZ is focused on the middle of the screen, thus it cannot be used in the footer and header of the SRV camera feeds.
- Scroll-To-Zoom: zoom-in and zoom-out by scrolling on the mouse.
- Pan-Tilt-Move: camera moves into a direction after clicking into the desired area of the camera feed.
- Area Zoom: camera zooms into the area drawn by the user.
- Move and reset buttons: camera movement can be controlled by the arrows and the magnifying glass icons in the right lower corner of the camera feed.
Zoom level can be reset to the default value with the Reset zoom icon.
- PTZ preset: Saving a particular view of a PTZ camera can be done by clicking the Presets drop-down, typing the desired title in the Add new preset field then clicking the plus button. To select an already added view, click its title in the drop-down.
Audio setting
The audio of a particular camera can be turned on or off by clicking the audio icon 
in the top right corner of the camera panel.
| Info |
|---|
| Only one camera of a room can have its audio turned on at a time. |
Recording setup
Clicking the Recording setup in the header prompts the Recording Setup pop-up window to appear where the Learners and Faculty (FON) can be added to a recording.
| Note |
|---|
The Learners/Staff dropdown only gets active, once Learner/FON Group has already been selected. |
| Info |
|---|
Selected participants show up as 'disabled' (greyed out) in the Learners dropdown. |
| Info | ||
|---|---|---|
| ||
Participants who have not been selected, are active in the dropdown and thus can be selected. |
Rooms
Rooms to be recorded can be selected from Room selector drop-down located at the top of the SRV screen.
| Note | ||
|---|---|---|
| ||
In CAE LearningSpace Experience, an Instructor manages the scenario on the patient simulator via the instructor workstation (tablet, control workstation) and LearningSpace captures the data of the simulator. (Therefore, no Sim Control Panel is available in any of the Recording views.) |
Toggle Panel Width/Height
With this functionality, the bottom- and side panels can be minimized in order to maximize the displayed camera- or media view.
| Note |
|---|
The toggle reveals itself by hovering over the bottom- or side panel, or on the panel border lines. When activated (i.e. camera view is maximized), the toggle arrows are displayed constantly. |
| Tip |
|---|
See also our Practical Recording and Recording - FAQ pages. |
Overview
Content Tools